EXACTLY HOW TO INSTALL A BATHTUB

Exactly How to Install a Bathtub

Exactly How to Install a Bathtub

Blog Article

Course Detail

Right here down the page you can discover additional dependable insight in relation to Installing A Bathtub.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a bath tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily available, the job can relocate easily; if you need to open up a wall to remove the old tub and position the new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually certified on your own for the job and are comfortable attempting it. Rather than employing a professional to take control of a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Possibilities are you might require a professional plumber to make tube connections.
This article will help you mount a brand-new bath tub in your washroom if you have actually currently gotten a brand-new bathtub as well as don't need to change the arrangement of your previous supply of water pipes.
Your tools and product list need to consist of the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Setup


    Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps unit to stop pressure on the tub.
    Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you use all of the provided washers.
    Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last position.

    Removing Old Touches


    If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the water system. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted gain access to that is often the situation.
    Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any old securing substance.
    Before proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.

    Installing the Bathtub


    Utilizing both wood boards under its feet, place the tub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 small points.
    The next objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the bath tub till the level reads level.
    To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
    Activate the water supply and check all joints and new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
    Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub must wait till the tub has actually been utilized a minimum of once as this will settle it into its final placement.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, then you will need a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the existent supply pipelines.
    If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next, position the tap in the placing opening in the bath/basin making sure that the washers remain in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer provided backnut. As soon as the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the location where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, causing problems with wetness as well as feasible leakages to the ceiling below.
    You can select from a variety of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can break rather early if you do not take into consideration this movement prior to securing.
    Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is a good idea to fit the floor tiles using waterproof or water-proof adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    I stumbled upon that page about A Step-by-Step Guide to Installing a Bathtub when exploring the search engines. Sharing is good. Helping others is fun. I appreciate reading our article about How to Install a Bathtub.




    Click Here!


    Report this page